Ametek Lx Series II Programming Manual Manuale Utente Pagina 80
- Pagina / 242
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Programming Manual Lx \ Ls Series II
76
4.18 Source Subsystem - Function
This subsystem programs the output function of the AC source.
Subsystem Syntax
[SOURce:]
FUNCtion
[:SHAPe]
[:IMMediate] <shape> Sets the periodic waveform shape
(SIN|SQU|CSIN|<user-defined>)
:MODE <mode> Sets the waveform shape mode (FIX|STEP|PULS|LIST)
:TRIGgered <shape> Sets the triggered transient shape
(SIN|SQU|CSIN|<user-defined>)
:CSINusoid <n> [THD] Sets the % of peak at which the clipped sine clips (or %
THD)
FUNCtion
This command selects the shape of the output voltage waveform as follows:
SINusoid A sinewave is output
SQUare A squarewave is output
CSINusoid The output is a clipped sine waveform. Both positive and negative peak
amplitudes are clipped at a value determined by the
SOURce:FUNCtion:SHAPe:CSINusoid setting.
<user_defined> The output shape is described by one of the user-defined waveform
tables.
The maximum peak voltage that the AC source can output is 425 V peak. This includes any
combination of voltage and function shape values. Therefore, the maximum value that can be
programmed depends on the peak-to-rms ratio of the selected waveform. For a sinewave, the
maximum voltage that can be programmed is 300 V rms.
Before programming a different waveform shape, the output voltage should be programmed to
zero volts. After the shape is changed, the voltage maybe programmed to the desired value.
Note: You cannot program a voltage that produces a higher volt-second on the output than a
300V rms sinewave.
Command Syntax [SOURce:]FUNCtion[:SHAPe][:IMMediate]<shape>
Parameters SINusoid|SQUare|CSINusoid|<waveform_name>
*RST Value SINusoid
Examples FUNC SIN FUNC USERNAME
Query Syntax [SOURce:]FUNCtion[:SHAPe]?
Returned Parameters <CRD>
Related Commands FUNC:MODE FUNC:TRIGVOLT
FUNCtion:MODE
This command determines how the waveform shape is controlled during a triggered output
transient. The choices are:
FIXed The waveform shape is unaffected by a triggered output transient.
STEP The waveform shape is programmed to the value set by
FUNCtion:TRIGgered when a triggered transient occurs.
- Lx \ Ls Series II 1
- AC Power Source 1
- Programming Manual 1
- SAFETY SYMBOLS 7
- Table of Contents 9
- Table of Figures 11
- Table of Tables 11
- 1. Introduction 12
- 1.2.1 Firmware differences 13
- 1.2.2 Hardware differences 13
- 2. Introduction to SCPI 16
- 2.2.3 The SCPI Command Tree 17
- 2.3 Using Queries 19
- 2.4 Coupled Commands 19
- 2.5.3 Headers 20
- 2.5.4 Query Indicator 21
- 2.5.6 Root Specifier 21
- 2.5.7 Message Terminator 21
- 2.6 SCPI Data Formats 22
- 3. System Considerations 24
- 3.2 USB Interface 25
- 3.2.2 USB Interface Use 31
- 3.3 LAN Option 32
- 3.3.5 Socket Port Number 36
- 3.4 RS232C Serial Interface 37
- 4. SCPI Command Reference 39
- 4.2 Subsystem Commands 40
- 4.3 Calibration Subsystem 41
- 4.4 Diagnostic Subsystem 43
- 4.5 Display Subsystem 44
- 4.6 Instrument Subsystem 46
- 4.7 Limit Subsystem 47
- 4.13 Output Subsystem 66
- 4.14 Power On Subsystem 71
- 4.24 System Commands 109
- 4.26 Trigger Subsystem 117
- (default) 118
- 5. Common Commands 122
- 5.1 *CLS 123
- 5.2 *ESR? 123
- 5.3 *IDN? 124
- 5.4 *OPC 124
- 5.5 *OPT? 124
- 5.6 *PSC 124
- 5.7 *RCL 125
- 5.8 *RST 126
- 5.9 *SAV 127
- 5.10 *SRE 127
- 5.11 *STB? 127
- 5.12 *TRG 128
- 5.13 *TST? 128
- 5.14 *WAI 129
- 6. Programming Examples 130
- 6.2.1 Waveform Shapes 132
- 6.2.2 Individual Phases 133
- 6.3 Coupled Commands 134
- FIXED mode 136
- STEP mode 136
- PULSE mode 136
- LIST mode 136
- 6.6 List Transients 138
- INIT[:IMM] 140
- 6.7.7 Generating Triggers 142
- 6.8 Making Measurements 143
- 6.8.2 Power Measurements 144
- 6.8.3 Harmonic Measurements 144
- Offset = 151
- 0 to 2^9 151
- Offset = - 4096 151
- Offset = - 2048 151
- Offset = 0 151
- 6.10.2 Download Sample 152
- 7.1 Power-On Conditions 154
- 7.2 Operation Status Group 154
- 151 155
- 7.6 Status Byte Register 160
- 7.7 Examples 161
- 7.8.1 Remote Inhibit (RI) 164
- 7.9 SCPI Command Completion 165
- 8. Option Commands 166
- 8.2.1 Introduction 167
- 8.2.3 GPIB Address 170
- 8.2.4 APE over RS232 170
- 8.2.5 Message Format 171
- 8.2.6 Numeric Data Field 171
- 8.2.7 Program Headers 172
- 8.2.9 APE Program Headers 174
- 8.2.14 Service Requests 184
- 181 185
- 8.3.1 Introduction 187
- 8.3.2 ABLE Language details 187
- 8.3.3 Language Extension 191
- 8.4 RTCA/DO-160D (-160) 192
- VOLTAGE SURGE, for details 194
- 8.6.1 Command Tree 200
- 8.7.1 Command Tree 207
- 219 223
- 220 224
- 221 225
- 222 226
- SCPI Version 227
- SCPI Confirmed commands 227
- 225 229
- PONS:SYNC[:SOUR] 229
- Appendix C: Error Messages 230
- 227 231
- 228 232
- 229 233
- 230 234
- 231 235
Prodotti e manuali riguardandi Apparecchiature Ametek Lx Series II Programming Manual
Apparecchiature Ametek MX CTSH Manuale Utente
(151 pagine)
(151 pagine)
Apparecchiature Ametek i Series Manuale Utente
(341 pagine)
(341 pagine)
Apparecchiature Ametek MX CTSL Manuale Utente
(157 pagine)
(157 pagine)
Apparecchiature Ametek i-iX Series II Manuale Utente
(258 pagine)
(258 pagine)
Apparecchiature Ametek HPD Series Manuale Utente
(58 pagine)
(58 pagine)
Apparecchiature Ametek APG-XT Manuale Utente
(36 pagine)
(36 pagine)
Apparecchiature Ametek PLA-PLW Manuale Utente
(128 pagine)
(128 pagine)
Apparecchiature Ametek FPDC Manuale Utente
(4 pagine)
(4 pagine)
Apparecchiature Ametek ACPS Manuale Utente
(4 pagine)
(4 pagine)
Apparecchiature Ametek HPAL Manuale Utente
(3 pagine)
(3 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale