Ametek Lx Series II Programming Manual Manuale Utente Pagina 68
- Pagina / 242
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Programming Manual Lx \ Ls Series II
64
OUTPut:PROTection:DELay
This command sets the delay time between the programming of an output change that produces
a CL or UNREG status condition and the recording of that condition by the Status Operation
Condition register. The delay prevents momentary changes in status that can occur during
programming from being registered as events by the status subsystem. In most cases these
temporary conditions are not considered an event, and to record them as such would be a
nuisance.
Command Syntax OUTPut:PROTection:DELay<NRf>
Parameters 0 to 32 | MINimum | MAXimum
Unit S (seconds)
*RST Value 100 milliseconds
Examples OUTP:PROT:DEL 75E-1
Query Syntax OUTPut:PROTection:DELay?
Returned Parameters <NR3>
Related Commands OUTP:PROT:CLE *RCL *SAV
OUTPut:RI[:LEVel]
This command sets the remote inhibit level mode. Factory default is LOW, which requires a
contact closure to open the output relay. The level can be reversed by setting it to HIGH. Once
set, the RI level setting is retained each time the power source is powered up. Note that this
command is only implement with firmware revision 1.69 or higher. Lower firmware revisions only
provide the default LOW setting.
Command Syntax OUTPut:RI:LEVel
Parameters LOW | HIGH
*RST Value LOW
Examples OUTP:RI:LEV HIGH
Query Syntax OUTP:RI:LEV?
Returned Parameters <CRD>
Related Commands OUTP OUTP:RI:MODE
OUTPut:RI:MODE
This command selects the mode of operation of the Remote Inhibit protection. The following
modes can be selected:
LATChing A TTL low at the RI input latches the output in the protection shutdown
state, which can only be cleared by OUTPut:PROTection:CLEar.
LIVE The output state follows the state of the RI input. A TTL low at the RI
input turns the output off; a TTL high turns the output on.
OFF The instrument ignores the RI input.
The RI output state is saved as part of an instrument setup using the *SAV command. It can be
made part of the power on setting if needed. The default state is LIVE.
Command Syntax OUTPut:RI:MODE <mode>
Parameters LATChing | LIVE | OFF
*RST Value OFF
Examples OUTP:RI:MODE LIVE
Query Syntax OUTPut:RI:MODE?
Returned Parameters <CRD>
Related Commands OUTP:PROT:CLE OUTP:RI:LEV
- Lx \ Ls Series II 1
- AC Power Source 1
- Programming Manual 1
- SAFETY SYMBOLS 7
- Table of Contents 9
- Table of Figures 11
- Table of Tables 11
- 1. Introduction 12
- 1.2.1 Firmware differences 13
- 1.2.2 Hardware differences 13
- 2. Introduction to SCPI 16
- 2.2.3 The SCPI Command Tree 17
- 2.3 Using Queries 19
- 2.4 Coupled Commands 19
- 2.5.3 Headers 20
- 2.5.4 Query Indicator 21
- 2.5.6 Root Specifier 21
- 2.5.7 Message Terminator 21
- 2.6 SCPI Data Formats 22
- 3. System Considerations 24
- 3.2 USB Interface 25
- 3.2.2 USB Interface Use 31
- 3.3 LAN Option 32
- 3.3.5 Socket Port Number 36
- 3.4 RS232C Serial Interface 37
- 4. SCPI Command Reference 39
- 4.2 Subsystem Commands 40
- 4.3 Calibration Subsystem 41
- 4.4 Diagnostic Subsystem 43
- 4.5 Display Subsystem 44
- 4.6 Instrument Subsystem 46
- 4.7 Limit Subsystem 47
- 4.13 Output Subsystem 66
- 4.14 Power On Subsystem 71
- 4.24 System Commands 109
- 4.26 Trigger Subsystem 117
- (default) 118
- 5. Common Commands 122
- 5.1 *CLS 123
- 5.2 *ESR? 123
- 5.3 *IDN? 124
- 5.4 *OPC 124
- 5.5 *OPT? 124
- 5.6 *PSC 124
- 5.7 *RCL 125
- 5.8 *RST 126
- 5.9 *SAV 127
- 5.10 *SRE 127
- 5.11 *STB? 127
- 5.12 *TRG 128
- 5.13 *TST? 128
- 5.14 *WAI 129
- 6. Programming Examples 130
- 6.2.1 Waveform Shapes 132
- 6.2.2 Individual Phases 133
- 6.3 Coupled Commands 134
- FIXED mode 136
- STEP mode 136
- PULSE mode 136
- LIST mode 136
- 6.6 List Transients 138
- INIT[:IMM] 140
- 6.7.7 Generating Triggers 142
- 6.8 Making Measurements 143
- 6.8.2 Power Measurements 144
- 6.8.3 Harmonic Measurements 144
- Offset = 151
- 0 to 2^9 151
- Offset = - 4096 151
- Offset = - 2048 151
- Offset = 0 151
- 6.10.2 Download Sample 152
- 7.1 Power-On Conditions 154
- 7.2 Operation Status Group 154
- 151 155
- 7.6 Status Byte Register 160
- 7.7 Examples 161
- 7.8.1 Remote Inhibit (RI) 164
- 7.9 SCPI Command Completion 165
- 8. Option Commands 166
- 8.2.1 Introduction 167
- 8.2.3 GPIB Address 170
- 8.2.4 APE over RS232 170
- 8.2.5 Message Format 171
- 8.2.6 Numeric Data Field 171
- 8.2.7 Program Headers 172
- 8.2.9 APE Program Headers 174
- 8.2.14 Service Requests 184
- 181 185
- 8.3.1 Introduction 187
- 8.3.2 ABLE Language details 187
- 8.3.3 Language Extension 191
- 8.4 RTCA/DO-160D (-160) 192
- VOLTAGE SURGE, for details 194
- 8.6.1 Command Tree 200
- 8.7.1 Command Tree 207
- 219 223
- 220 224
- 221 225
- 222 226
- SCPI Version 227
- SCPI Confirmed commands 227
- 225 229
- PONS:SYNC[:SOUR] 229
- Appendix C: Error Messages 230
- 227 231
- 228 232
- 229 233
- 230 234
- 231 235
Prodotti e manuali riguardandi Apparecchiature Ametek Lx Series II Programming Manual
Apparecchiature Ametek MX CTSH Manuale Utente
(151 pagine)
(151 pagine)
Apparecchiature Ametek i Series Manuale Utente
(341 pagine)
(341 pagine)
Apparecchiature Ametek MX CTSL Manuale Utente
(157 pagine)
(157 pagine)
Apparecchiature Ametek i-iX Series II Manuale Utente
(258 pagine)
(258 pagine)
Apparecchiature Ametek HPD Series Manuale Utente
(58 pagine)
(58 pagine)
Apparecchiature Ametek APG-XT Manuale Utente
(36 pagine)
(36 pagine)
Apparecchiature Ametek PLA-PLW Manuale Utente
(128 pagine)
(128 pagine)
Apparecchiature Ametek FPDC Manuale Utente
(4 pagine)
(4 pagine)
Apparecchiature Ametek ACPS Manuale Utente
(4 pagine)
(4 pagine)
Apparecchiature Ametek HPAL Manuale Utente
(3 pagine)
(3 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale