Ametek Lx Series II Programming Manual Manuale Utente Pagina 210
- Pagina / 242
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Programming Manual Lx \ Ls Series II
206
MS704:REVision
This command sets the RTCA DO-160 test standard revision to be used. The test levels and
duration are typically a function of the test standard revision.
Command Syntax MS704:REVision
Parameters A | B | C | D | E | F
Examples MS704:REV F
Query Syntax MS704:REV?
Returned Parameters <CRD>
MS704:SKIP
This command skips the currently active test step. This command may be used to proceed
immediately to the next step in a test sequence.
Note that if a test steps is normally repeated more than once, the SKIP command only skips the
repetition that is active. For test conditions with more than one repeat, to skip to the next test
condition will require a SKIP command for each repeat to be issued. Alternatively, the ABORt
command may be used to abort the entire test in progress.
Command Syntax MS704:SKIP
Parameters none
Examples MS704:SKIP
Query Syntax none
MS704:STATus?
This is a query only command that reports the test progress status of the test step in progress.
The status returned is either “IDLE” if no tests are running or the test number, test condition and
time remaining till completion of the test in minutes and seconds. This command query may be
used to poll the progress of a test.
Command Syntax MS704:STATus?
Parameters none
Examples MS704:STAT?
Query Syntax MS704:STAT?
Returned Parameters <CRD>
Response SAC102 A 03:32
MS704:STEP
This command sets the execution mode for each test step execution. Available settings are
SINGLE or CONTINUOUS. In single step mode, a selected test and test condition (A..Z, AA..ZZ)
will be run by itself. This allows an individual test condition to be executed. In continuous mode, all
remaining test conditions for the selected test will be run once the selected test condition is
completed. Thus, in continuous mode, the rest of the test will run from the selected test condition
forward.
Command Syntax MS704:STEP
Parameters SINGle | CONTinuous
Examples MS704:STEP SING
Query Syntax MS704:STEP?
Returned Parameters <CRD>
- Lx \ Ls Series II 1
- AC Power Source 1
- Programming Manual 1
- SAFETY SYMBOLS 7
- Table of Contents 9
- Table of Figures 11
- Table of Tables 11
- 1. Introduction 12
- 1.2.1 Firmware differences 13
- 1.2.2 Hardware differences 13
- 2. Introduction to SCPI 16
- 2.2.3 The SCPI Command Tree 17
- 2.3 Using Queries 19
- 2.4 Coupled Commands 19
- 2.5.3 Headers 20
- 2.5.4 Query Indicator 21
- 2.5.6 Root Specifier 21
- 2.5.7 Message Terminator 21
- 2.6 SCPI Data Formats 22
- 3. System Considerations 24
- 3.2 USB Interface 25
- 3.2.2 USB Interface Use 31
- 3.3 LAN Option 32
- 3.3.5 Socket Port Number 36
- 3.4 RS232C Serial Interface 37
- 4. SCPI Command Reference 39
- 4.2 Subsystem Commands 40
- 4.3 Calibration Subsystem 41
- 4.4 Diagnostic Subsystem 43
- 4.5 Display Subsystem 44
- 4.6 Instrument Subsystem 46
- 4.7 Limit Subsystem 47
- 4.13 Output Subsystem 66
- 4.14 Power On Subsystem 71
- 4.24 System Commands 109
- 4.26 Trigger Subsystem 117
- (default) 118
- 5. Common Commands 122
- 5.1 *CLS 123
- 5.2 *ESR? 123
- 5.3 *IDN? 124
- 5.4 *OPC 124
- 5.5 *OPT? 124
- 5.6 *PSC 124
- 5.7 *RCL 125
- 5.8 *RST 126
- 5.9 *SAV 127
- 5.10 *SRE 127
- 5.11 *STB? 127
- 5.12 *TRG 128
- 5.13 *TST? 128
- 5.14 *WAI 129
- 6. Programming Examples 130
- 6.2.1 Waveform Shapes 132
- 6.2.2 Individual Phases 133
- 6.3 Coupled Commands 134
- FIXED mode 136
- STEP mode 136
- PULSE mode 136
- LIST mode 136
- 6.6 List Transients 138
- INIT[:IMM] 140
- 6.7.7 Generating Triggers 142
- 6.8 Making Measurements 143
- 6.8.2 Power Measurements 144
- 6.8.3 Harmonic Measurements 144
- Offset = 151
- 0 to 2^9 151
- Offset = - 4096 151
- Offset = - 2048 151
- Offset = 0 151
- 6.10.2 Download Sample 152
- 7.1 Power-On Conditions 154
- 7.2 Operation Status Group 154
- 151 155
- 7.6 Status Byte Register 160
- 7.7 Examples 161
- 7.8.1 Remote Inhibit (RI) 164
- 7.9 SCPI Command Completion 165
- 8. Option Commands 166
- 8.2.1 Introduction 167
- 8.2.3 GPIB Address 170
- 8.2.4 APE over RS232 170
- 8.2.5 Message Format 171
- 8.2.6 Numeric Data Field 171
- 8.2.7 Program Headers 172
- 8.2.9 APE Program Headers 174
- 8.2.14 Service Requests 184
- 181 185
- 8.3.1 Introduction 187
- 8.3.2 ABLE Language details 187
- 8.3.3 Language Extension 191
- 8.4 RTCA/DO-160D (-160) 192
- VOLTAGE SURGE, for details 194
- 8.6.1 Command Tree 200
- 8.7.1 Command Tree 207
- 219 223
- 220 224
- 221 225
- 222 226
- SCPI Version 227
- SCPI Confirmed commands 227
- 225 229
- PONS:SYNC[:SOUR] 229
- Appendix C: Error Messages 230
- 227 231
- 228 232
- 229 233
- 230 234
- 231 235
Prodotti e manuali riguardandi Apparecchiature Ametek Lx Series II Programming Manual
Apparecchiature Ametek MX CTSH Manuale Utente
(151 pagine)
(151 pagine)
Apparecchiature Ametek i Series Manuale Utente
(341 pagine)
(341 pagine)
Apparecchiature Ametek MX CTSL Manuale Utente
(157 pagine)
(157 pagine)
Apparecchiature Ametek i-iX Series II Manuale Utente
(258 pagine)
(258 pagine)
Apparecchiature Ametek HPD Series Manuale Utente
(58 pagine)
(58 pagine)
Apparecchiature Ametek APG-XT Manuale Utente
(36 pagine)
(36 pagine)
Apparecchiature Ametek PLA-PLW Manuale Utente
(128 pagine)
(128 pagine)
Apparecchiature Ametek FPDC Manuale Utente
(4 pagine)
(4 pagine)
Apparecchiature Ametek ACPS Manuale Utente
(4 pagine)
(4 pagine)
Apparecchiature Ametek HPAL Manuale Utente
(3 pagine)
(3 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale