Ametek Lx Series II Programming Manual Manuale Utente Pagina 177
- Pagina / 242
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Programming Manual Lx \ Ls Series II
173
Argument
Extension
Data returned
Definition
0.00 to 27.00
PZM
A, B, C
0 to 359.9
Measured phase B and C output phase angle
relative to A. A is always 0.0
REG
0 to 15
Contents of Reg
Talk contents of register
RNG
None
0 to 270.0
Programmed range and limit
SRQ
None
0, 1 or 2
Programmed SRQ status
VLT
A, B, C
0.0 to 400.0
Measured output voltage
THD
A, B, C
0 to 20
Programmed total harmonic distortion
NOTE: If the A, B or C Extension is not sent with the argument, all phases will be reported
Table 8-4: APE Language TLK Arguments
8.2.11 Examples - APE Programming Commands
This section provides APE syntax examples and programming techniques. These examples are
provided for reference only and are shown in no specific order.
To program Amplitude (AMP)
The AMP header with the optional A, B or C extension is used to identify the amplitude command.
The argument is a numeric data field from 0.0 to the limit set by the RNG value. An attempt to
program a value higher than this value will generate an error and a SRQ on the GPIB.
The following ASCII strings will program the voltage given in the left column:
To Set: Issue:
A, B, C 0.0 volts AMP0 or AMPA0AMPB0AMPC0
A, B, C 10.5 volts AMP10.5 or AMP1.05E1 or AMP105E-1
A, B, C 100 volts AMP100 or AMP100.0 or AMP1E2
A, B = 110.5, C = 115 AMPA110.5AMPB110.5AMPC115
or AMP110.5AMPC115
To program Frequency (FRQ)
The FRQ header is used to identify the following numeric data as frequency. The following string
will program the frequency to 60.56 Hz.
FRQ 60.56
To program Phase angle (PHZ)
The PHZ header with the optional A, B or C extension is used to identify the following numeric
data as phase. The PHZ header sent with no extension will program the B and C outputs in
phase with phase A. The phase of the A output will lead the EXT SNC signal by the value
programmed. The following example will program the phase A output to 90 degrees relative to an
external sync signal when operating in the EXT SNC mode:
PHZA 90
The following example will program phase B to 240.5 degrees and phase C to 119.3 degrees
leading phase A.
PHZB 240.5 PHZ C 119.3
- Lx \ Ls Series II 1
- AC Power Source 1
- Programming Manual 1
- SAFETY SYMBOLS 7
- Table of Contents 9
- Table of Figures 11
- Table of Tables 11
- 1. Introduction 12
- 1.2.1 Firmware differences 13
- 1.2.2 Hardware differences 13
- 2. Introduction to SCPI 16
- 2.2.3 The SCPI Command Tree 17
- 2.3 Using Queries 19
- 2.4 Coupled Commands 19
- 2.5.3 Headers 20
- 2.5.4 Query Indicator 21
- 2.5.6 Root Specifier 21
- 2.5.7 Message Terminator 21
- 2.6 SCPI Data Formats 22
- 3. System Considerations 24
- 3.2 USB Interface 25
- 3.2.2 USB Interface Use 31
- 3.3 LAN Option 32
- 3.3.5 Socket Port Number 36
- 3.4 RS232C Serial Interface 37
- 4. SCPI Command Reference 39
- 4.2 Subsystem Commands 40
- 4.3 Calibration Subsystem 41
- 4.4 Diagnostic Subsystem 43
- 4.5 Display Subsystem 44
- 4.6 Instrument Subsystem 46
- 4.7 Limit Subsystem 47
- 4.13 Output Subsystem 66
- 4.14 Power On Subsystem 71
- 4.24 System Commands 109
- 4.26 Trigger Subsystem 117
- (default) 118
- 5. Common Commands 122
- 5.1 *CLS 123
- 5.2 *ESR? 123
- 5.3 *IDN? 124
- 5.4 *OPC 124
- 5.5 *OPT? 124
- 5.6 *PSC 124
- 5.7 *RCL 125
- 5.8 *RST 126
- 5.9 *SAV 127
- 5.10 *SRE 127
- 5.11 *STB? 127
- 5.12 *TRG 128
- 5.13 *TST? 128
- 5.14 *WAI 129
- 6. Programming Examples 130
- 6.2.1 Waveform Shapes 132
- 6.2.2 Individual Phases 133
- 6.3 Coupled Commands 134
- FIXED mode 136
- STEP mode 136
- PULSE mode 136
- LIST mode 136
- 6.6 List Transients 138
- INIT[:IMM] 140
- 6.7.7 Generating Triggers 142
- 6.8 Making Measurements 143
- 6.8.2 Power Measurements 144
- 6.8.3 Harmonic Measurements 144
- Offset = 151
- 0 to 2^9 151
- Offset = - 4096 151
- Offset = - 2048 151
- Offset = 0 151
- 6.10.2 Download Sample 152
- 7.1 Power-On Conditions 154
- 7.2 Operation Status Group 154
- 151 155
- 7.6 Status Byte Register 160
- 7.7 Examples 161
- 7.8.1 Remote Inhibit (RI) 164
- 7.9 SCPI Command Completion 165
- 8. Option Commands 166
- 8.2.1 Introduction 167
- 8.2.3 GPIB Address 170
- 8.2.4 APE over RS232 170
- 8.2.5 Message Format 171
- 8.2.6 Numeric Data Field 171
- 8.2.7 Program Headers 172
- 8.2.9 APE Program Headers 174
- 8.2.14 Service Requests 184
- 181 185
- 8.3.1 Introduction 187
- 8.3.2 ABLE Language details 187
- 8.3.3 Language Extension 191
- 8.4 RTCA/DO-160D (-160) 192
- VOLTAGE SURGE, for details 194
- 8.6.1 Command Tree 200
- 8.7.1 Command Tree 207
- 219 223
- 220 224
- 221 225
- 222 226
- SCPI Version 227
- SCPI Confirmed commands 227
- 225 229
- PONS:SYNC[:SOUR] 229
- Appendix C: Error Messages 230
- 227 231
- 228 232
- 229 233
- 230 234
- 231 235
Prodotti e manuali riguardandi Apparecchiature Ametek Lx Series II Programming Manual
Apparecchiature Ametek MX CTSH Manuale Utente
(151 pagine)
(151 pagine)
Apparecchiature Ametek i Series Manuale Utente
(341 pagine)
(341 pagine)
Apparecchiature Ametek MX CTSL Manuale Utente
(157 pagine)
(157 pagine)
Apparecchiature Ametek i-iX Series II Manuale Utente
(258 pagine)
(258 pagine)
Apparecchiature Ametek HPD Series Manuale Utente
(58 pagine)
(58 pagine)
Apparecchiature Ametek APG-XT Manuale Utente
(36 pagine)
(36 pagine)
Apparecchiature Ametek PLA-PLW Manuale Utente
(128 pagine)
(128 pagine)
Apparecchiature Ametek FPDC Manuale Utente
(4 pagine)
(4 pagine)
Apparecchiature Ametek ACPS Manuale Utente
(4 pagine)
(4 pagine)
Apparecchiature Ametek HPAL Manuale Utente
(3 pagine)
(3 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale