Ametek BPS Series Programming Manual Manuale Utente Pagina 218
- Pagina / 226
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
AMETEK Programmable Power BPS / MX / RS Series SCPI Programming Manual
218 Manual P/N 7003-961 Rev AA
Number Message String Cause Remedy
27 “Frequency error” Frequency is out of
allowable range.
Indicates a problem with
programmable controller.
28 “Phase error” Incorrect phase
29 “DC component
exceeds limit”
The waveform
selected contains a
DC offset that
exceeds the AC
mode capability.
Select AC+DC mode.
30 “Amplifier fault” Amplifier fault. Contact customer service.
31 “Warning negative
power near limit”
Approaching limit on
the amount of power
that can be fed back
into the supply by an
active load. This is a
warning only.
Stop increasing power feedback into
the power supply. Typically occurs
when using AC inverters. If power
increases further, an error 32 will be
generated.
32 “Negative power fault” Too much power fed
back. Power source
output disconnected.
Reduce the amount of power being
fed back into the power source.
Table 8-4 : Error Messages
- BPS / Mx / RS Series 1
- SCPI Programming Manual 1
- WARNING 4
- SAFETY SYMBOLS 5
- Warranty Period: 1 Year 6
- WARRANTY TERMS 6
- PRODUCT RETURN PROCEDURE 6
- Table of Contents 7
- Table of Figures 9
- Table of Tables 9
- Introduction 10
- Model BPS Series 11
- External References 11
- Introduction to Programming 12
- Introduction to SCPI 14
- Types of SCPI Messages 15
- The SCPI Command Tree 15
- Using Queries 17
- Structure of a SCPI Message 17
- The Message Unit 17
- Combining Message Units 18
- Headers 19
- Query Indicator 19
- Message Unit Separator 19
- Root Specifier 20
- Message Terminator 20
- SCPI Data Formats 21
- Numerical Data Formats 21
- Character Data 21
- GPIB Controllers 22
- Agilent 82350 Driver 22
- RS232C Interface 24
- Serial Cable Diagram 25
- USB Driver Installation 26
- USB Interface 26
- USB Interface Use 34
- LAN Interface Option 35
- MAC Address 35
- Setting the TCP/IP Address 35
- Socket Port Number 37
- IP Ping 37
- SCPI Command Reference 38
- Calibration Subsystem 39
- [:SOURce] 40
- :HRANge 40
- :IMPedance 40
- Current Measurement 42
- Voltage Measurement 44
- Output Phase 46
- Output - AC Voltage 47
- Output - DC Voltage 49
- Display Subsystem 51
- Instrument Subsystem 53
- Current Array Data 56
- Voltage Array Data 60
- Phase Measurement Subsystem 67
- Power Measurement Subsystem 68
- Output Subsystem 73
- Output Relay 73
- Output Protection 74
- Output Remote Inhibit Modes 74
- External Trigger Output 76
- Source Subsystem - Current 79
- Source Subsystem - Frequency 81
- Source Subsystem - Limit 86
- Source Subsystem - List 90
- List - Count 91
- List - Dwell 91
- List - Frequency 92
- List - Repeat 94
- List - Step 94
- List:TTL Trigger Out 95
- List:Voltage 96
- Source Subsystem - Mode 98
- Source Subsystem - Phase 99
- Source Subsystem - PONSetup 100
- Source Subsystem - Pulse 104
- Source Subsystem - Voltage 107
- Status Subsystem Commands 113
- System Commands 117
- Trigger Subsystem 126
- Common Commands 131
- 5.1 *CLS 132
- 5.2 *ESE 133
- 5.3 *ESR? 133
- 5.4 *IDN? 134
- 5.5 *OPC 134
- 5.6 *OPT? 135
- 5.7 *PSC 136
- 5.8 *RCL 136
- 5.9 *RST 137
- 5.10 *SAV 138
- 5.11 *SRE 138
- 5.12 *STB? 139
- 5.13 *TRG 140
- 5.14 *WAI 140
- Programming Examples 141
- Programming the Output 142
- Power-on Initialization 142
- Enabling the Output 142
- AC Voltage and Frequency 142
- Programming the Output Phase 144
- Current Limit 144
- Waveform Shapes 145
- Individual Phases 146
- Coupled Commands 147
- FIXED mode 149
- STEP mode 149
- PULSE mode 149
- LIST mode 149
- Step and Pulse Transients 150
- List Transients 151
- Triggering Output Changes 153
- Trigger System Model 153
- Generating Triggers 155
- Acquiring Measurement Data 156
- Power Measurements 157
- Frequency Measurements 157
- Harmonic Measurements 158
- Triggering Measurements 159
- TRIGGER RECEIVED 160
- INIT[:IMM]:ACQ 160
- 4096 DATA POINTS 163
- Trigger System Summary 164
- Status Registers 165
- Questionable Status Group 168
- Standard Event Status Group 169
- Status Byte Register 169
- Examples 170
- SCPI Command Completion 171
- Option Commands 172
- IEC 1000-4-11 (-411) 173
- IEC 1000-4-13 (-413) 177
- IEC 1000-4-13 Subsystem 177
- Interharmonics Subsystem 188
- RTCA/DO-160D (-160) 190
- VOLTAGE SURGE, for detail 192
- VOLTAGE UNDER 192
- MIL-STD 704E (-704) 197
- AC System 197
- DC System 198
- Programming Considerations 198
- OMNI Reference Impedance 200
- Watt Hour Meter (-WHM) 201
- Current Sink Option (-SNK) 202
- SCPI Version 212
- Appendix C: Error Messages 213
- Table 8-4 : Error Messages 218
Prodotti e manuali riguardandi Apparecchiature Ametek BPS Series Programming Manual
Apparecchiature Ametek BPS Series Manuale Utente
(153 pagine)
(153 pagine)
Apparecchiature Ametek DLM Series Manuale Utente
(74 pagine)
(74 pagine)
Apparecchiature Ametek M133 Manuale Utente
(8 pagine)
(8 pagine)
Apparecchiature Ametek M130 Manuale Utente
(99 pagine)
(99 pagine)
Apparecchiature Ametek CTS 3.0 Manuale Utente
(166 pagine)
(166 pagine)
Apparecchiature Ametek CSW Series Manuale Utente
(174 pagine)
(174 pagine)
Apparecchiature Ametek 2003RP Manuale Utente
(126 pagine)
(126 pagine)
Apparecchiature Ametek 2001RP Manuale Utente
(131 pagine)
(131 pagine)
Apparecchiature Ametek RS Series Manuale Utente
(228 pagine)
(228 pagine)
Apparecchiature Ametek MX15 Series Manuale Utente
(184 pagine)
(184 pagine)
Apparecchiature Ametek Lx Series II Manuale Utente
(226 pagine)
(226 pagine)
ACTi A1D-M2N-V2.05.12-AC podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Nie ACTi A1D-M2N-V2.05.12-AC.
Dostarczamy 1 pdf podręczników ACTi A1D-M2N-V2.05.12-AC do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commenti su questo manuale